Common Problems with Pumps: Know Your Pump Anatomy to Look for Impending Pump Failure

The pumps in a New York City condo or co-op building keep many systems running smoothly, especially those related to the boiler and plumbing, as well as the disposal of waste. Knowing about basic centrifugal pump anatomy can help you identify common problems with pumps, so you can fix them before a pump fails completely.

While every pump is built with slight differences in its design, there are parts that are shared with all centrifugal pumps. Here are some things to look for that could indicate one of your pumps is going to go on the fritz soon. Catch these problems now, and you can save yourself a lot of time, headaches, and money.

Electrical Components

Power for the motor

Today’s pumps are almost always powered by electricity, which means these elements must be working properly for the pump to function as desired. If you observe any of the following, it could mean the electrical power for your pump isn’t working right. Be careful, as these problems can also cause shock to workers or issues with other items on the same circuit:

  • Loose or broken switch – causes the pump to either run continuously, not turn on, or run intermittently, not always when it should
  • Frayed, loose, or broken wires – can mean the pump isn’t getting adequate power and may trip circuit breakers or cause flickering lights; can also cause sparks or risk of fire
  • Broken or melted plug – (for pumps that aren’t hardwired) must be replaced immediately, as this is a fire danger and may be caused by the pump or, more likely, by the outlet where the plug has been used

Pump Casing

Protection for the pump’s vital parts

The pump interior is protected by a casing, also sometimes called a housing or cover. The pump casing is particularly important if the pump is moving hot water or steam because it protects people working around the pump from burn injuries. Usually, thermal casing inside the outer housing adds more insulation.

Other parts related to the pump casing include:

  • Inlet – where fluid enters the pump
  • Outlet – also called the discharge end, where fluid exits the pump
  • Mounting system – used to hold the pump in place, whether by straps, screws, plates, or other means

If you have a leak coming from the pump, it could be from a breach in the casing. If the housing is quite old or has been corroded by acidic water, it should be replaced. Otherwise, you risk damaging the pump’s internal components. It could also be due to a problem with a seal (see below).

Noisy pumps can be caused by multiple things. However, if the noise is also accompanied by excess vibration, your first suspect should be a loose mounting.

Seals

Prevention of leakage

Water and other types of centrifugal pumps use a variety of seals, gaskets, and O-rings to prevent liquid from leaking out. These are found throughout the pump structure anywhere protection is needed. If you notice a leak in your pump and have ruled out a problem with the casing, a seal problem is the likely culprit.

Pump seals should be replaced as soon as you notice they are cracked, hardened, or misshapen. This is a relatively inexpensive part that can save you having to replace the entire pump.

Valves

Directing the flow of liquid

Pump valves are parts that dictate which way liquid can flow in the mechanism, much in the same way valves in your heart and circulatory system determine the flow of blood. Valves are designed to keep liquid moving in one direction so it doesn’t flow backwards (upstream).

A broken, clogged, or dirty valve can be another cause of pump leaks. Bad valves can also result in lowered pressure from the outlet side or fluid backing up on the inlet side of a pump.

Just like worn seals should be replaced right away, so should old valves that have outlived their usefulness. If a valve is only lightly clogged with sediment or mineral scale, it can usually be cleaned with something acidic (vinegar or lemon juice) and returned to its place.

Impeller

Essential for moving fluid

The part that does all the work in a centrifugal pump is the impeller. This looks like a fan with blades that rotate and push liquid to its destination. There are many different structures for impellers, and often they are fully covered or covered on one side (shrouded).

A problem with your impeller will affect the entire pump operation, so it’s vital that impeller problems be addressed immediately. Common issues include:

  • Clogged impellers – same as valves, above
  • Mechanical issues with the shaft connecting the impeller to the motor
  • Pitting – a sign of pump cavitation, the result of pressure imbalances that cause the liquid being pumped to turn into a vapor

Cavitation can be disastrous for a pump. If you notice pitting on your pump’s impeller, it’s best to alert your pump specialists. It could be the pump’s settings need to be adjusted; it’s also possible the pump size or inlet/outlet size are wrong for the demand being placed on it. A noisy or vibrating pump that’s not caused by a loose mounting part may be a sign of cavitation.

Lubrication

Necessary for smooth operation

Like the engine in your car, a pump needs lubrication to keep running without friction. Therefore, it’s equipped with a variety of lubrication mechanisms. As well as oiling the pump, you may need to clean or replace bearings regularly. If you’re not sure how to do this, Antler Pumps is happy to come out and do it for you, as part of our regular pump maintenance checklist.

How do you know if lubrication is an issue? You typically hear loud screeching noises or scraping sounds. The pump may also overheat and shut down.

Pump Sensors

Triggering the pump to turn on

Some pumps have sensors that tell them when to turn on. Three common pumps that use this mechanism are:

  • Sewage ejector pumps (aka sewage grinder pumps)
  • Sump pumps
  • Boiler automatic water feeder pumps

If you have one of these pumps that is either not turning on when it should or that runs without stopping, it may well be the sensor is stuck. A thorough cleaning and check to make sure the sensor is able to move freely should fix the problem.

Do you have a pump problem that is out of your wheelhouse and needs professional attention? Don’t wait until your pump fails to take action. Call Antler Pumps today at 212-534-2500 to schedule an appointment.

Our Privacy Policy

Omnia Mechanical Group(the “Company”) strives to ensure the highest standards for property listings and customer information privacy. Please review the following statement to learn about our company practices and policies. Please be aware that our Privacy Policy is subject to change at any time.

1. Purpose.

This Privacy Policy (“the Policy”) provides information on how the Company uses your personal information. By agreeing to the Policy, you agree to our collection and use of your personal information as described in the Policy. This Privacy Policy is effective for all new users of Sanitaryplumbing.com.

2. Personal Information.

You can browse some areas of omniagroup.nyc (“the Website”) without being a registered user. However, certain activities do require registration. (You consent to the transfer and storage of your information by registering with omniagroup.nyc).

3. Use of Information.

Our primary purpose in collecting personal information is to provide you with a safe and user-friendly experience. For example, the Company may use your personal information to:

  • Improve our services and the Website’s content and layout;
  • Provide the services and necessary customer support you request;
  • Resolve disputes, collect fees, and troubleshoot problems;
  • Track and record customer satisfaction with our services;
  • Protect the Company against error and fraud;
  • Inform you of special promotions and announcements;
  • Enforce our agreements, terms, conditions, and policies; and
  • As otherwise described to you at the time of collection.

We may occasionally ask you to complete optional surveys. These surveys are used to improve and customize your experience with Sanitaryplumbing.com.

The Company always provides you the ability to opt-out of further communication such as promotions and surveys; see the Opt-Out section below.

The Company does not share any of your personal information with outside organizations, companies, individuals, etc. The only exception to this standard is if such a disclosure is reasonably necessary to respond to any and all legal processes.

4. Links to Other Sites.

The Website may have links to other websites that may collect personally identifiable information about you. The Company is not responsible for the privacy practices of the content of those linked websites.

5. Safety & Security Precautions.

The Website has strict security measures in place to protect you and your information from fraud. Once your information is provided to Omnia Mechanical Group, we strive to ensure the confidentiality of your identity and information.

6. Opt-Out.

The Company provides you with the opportunity to opt-out of receiving promotional and other non-essential, marketing-related communications from Omnia Mechanical Group. If you would like to opt-out of these select communications, please see any of the Company’s email communications and follow the directions indicated.

7. Account Protection.

Your password ensures the security of your account. When choosing a password, the Company suggests using various characters. It is highly recommended that you do not disclose your Sanitaryplumbing.com password to anyone. (If you do disclose your password or your personal information with others, you are responsible for all actions taken in the name of your account.) If the security of your password is compromised for any reason, please contact the Company immediately.

8. Accuracy of Information

The Company does not guarantee the accuracy of information for any and all of its properties on the Website, and is not responsible for any errors or misrepresentations (made by Renters, the Client, or otherwise).

9. Cookies

The Company may place a small cookie on your computer’s hard drive. This allows us to personalize your use on the Website. In order to maximize the functionality and usability of the Website, you must set your browser’s preferences to allow both permanent and temporary cookies.

10. Changing Your Personal Information.

Should your personal information change, please immediately update your information on the Website. This will ensure the accuracy of our records. The Company does retain personal information from closed accounts in order to comply with law and collect and disburse any fees owed.

11. Third Parties

This Privacy Policy addresses only the use of information we collect from you. Since omniagroup.nyc does not control the privacy policies of third parties, you are subject to the privacy policies of those third parties. It is advisable that you consult with the management of third parties before you disclose your personal information to others.

12. General

We may amend this Privacy Policy at any time by posting the amended terms on the Website. All amended terms are immediately effective after they are initially posted on the Website.

13. Privacy Policy Questions & Concerns

Questions and/or concerns regarding the Policy should be emailed to the following email address: info@omniagroup.nyc.