What Is the Purpose of Steam Traps?

When safeguarding the boiler system in your apartment building, it’s important to remember to check your steam traps. If you’re new to property ownership or don’t spend a lot of time working with boilers, you might be fuzzy about “What is the purpose of steam traps?” This post will review their function and discuss common problems we see when servicing them. We’ll also review the three main kinds of steam traps available to you. You want to keep steam traps in tip-top condition, as they affect the efficiency of your boiler and, by default, your energy bills. When your steam traps work properly, you can save money all throughout the heating season.

A Brief Return to Physics Class

Defining steam

There are two states of matter that we deal with when talking about boilers: liquid and gas. When water is below the boiling point, it’s in the liquid phase. Once it starts to boil at 212 degrees Fahrenheit and evaporate, it becomes steam, which is the gas phase of water. Steam eventually cools and becomes liquid again, which is known as condensate. You probably have a condensate return system that channels cooled radiator steam back to your boiler.

How Steam Traps Work

Isolating steam from air and condensate

Likewise, you want to separate steam from air and condensate in the heating system. There are multiple benefits to doing this:

  • The steam can be used again without going through the phase changes described above.
  • Reutilizing steam can save money because your boiler doesn’t have to fire as often to heat water and make steam.
  • Running your boiler less frequently is better for the environment because fewer emissions are produced.
  • Trapping steam in the system and removing air and condensate can prevent water hammer, that annoying clanging you hear sometimes in pipes and radiators.

Unless you have a fairly small property, you likely have a series of steam traps that work together along your steam pipes. These steam traps typically fall into one of three categories, as defined below, based on their mechanism of action.

Different Types of Steam Traps

Thermostatic steam traps

These traps operate by sensing temperature differentials and can tell the difference between steam and condensate at the same pressure. A sensor detects condensate and lets it drain out via a valve.

Mechanical steam traps

This type of trap uses density to detect steam and condensate via a simple float mechanism. If you have steam traps that look like buckets, you likely have mechanical steam traps.

Thermodynamic steam traps

Using both pressure measurements and volumetrics, thermodynamic steam traps are smaller and less expensive than other types of traps. However, they’re also somewhat less efficient, as they lose a bit of steam as they work.

Steam Trap Servicing

Problems we see frequently

We see many of the same problems when it comes to steam traps in New York City apartment buildings. One of the most common is the steam trap remaining open when it should close. A clue this is happening is your boiler firing more than it should because it’s working harder to produce steam. You’ll observe that your fuel bills are higher, and your water expenses may be higher too, with the automatic boiler feeder constantly sending fresh water to the boiler. If the boiler can’t keep up, you might also hear from tenants that they aren’t getting enough heat from their radiators.

Sometimes the opposite happens, and the steam trap remains closed when it should open. When this happens, you’ll find less condensate returned to the boiler. Like when a steam trap fails in the open position, this problem also results in the boiler overworking and in less heat for occupants. However, you’ll also hear water hammer in the system as that extra condensate battles with steam and air.

Dirty steam traps can result from a multitude of factors:

  • Old age and traps nearing the end of their lifespan
  • Pipes too narrow for the system
  • Poor water filtration (sediment or mineral scale accumulation)
  • Wrong or excess chemicals used in boiler water treatment
  • Lack of regular maintenance

You might have dirty steam traps if you notice valves in other parts of your boiler system are clogged, encrusted, or malfunctioning. They might leak or have unusual wear, such as hardened or cracked parts. You might also notice you’re replacing valves more often than you think is right.

Of course, you could have the cleanest and most expensive steam traps in your property. But if they’re not sized right for your boiler system, or if they’re not installed properly, they won’t get the job done. That’s why it’s essential that you have boiler professionals like Calray Boilers put your steam traps in place and service them regularly.

Every property is different, and your heating system’s unique anatomy demands a tailored approach. We can give you a consultation that examines all aspects of your system and helps you choose the right components, including steam traps for efficiency and cost savings.

Whether you would like to have your steam traps checked or upgrade your steam trap system, Calray Boilers is here to help. You can call us at 212-722-5506, or use our easy online form to schedule a service visit at your convenience.


What Is the Purpose of Steam Traps?

When safeguarding the boiler system in your apartment building, it’s important to remember to check your steam traps. If you’re new to property ownership or don’t spend a lot of time working with boilers, you might be fuzzy about “What is the purpose of steam traps?” This post will review their function and discuss common problems we see when servicing them. We’ll also review the three main kinds of steam traps available to you. You want to keep steam traps in tip-top condition, as they affect the efficiency of your boiler and, by default, your energy bills. When your steam traps work properly, you can save money all throughout the heating season.

A Brief Return to Physics Class

Defining steam

There are two states of matter that we deal with when talking about boilers: liquid and gas. When water is below the boiling point, it’s in the liquid phase. Once it starts to boil at 212 degrees Fahrenheit and evaporate, it becomes steam, which is the gas phase of water. Steam eventually cools and becomes liquid again, which is known as condensate. You probably have a condensate return system that channels cooled radiator steam back to your boiler.

How Steam Traps Work

Isolating steam from air and condensate

Likewise, you want to separate steam from air and condensate in the heating system. There are multiple benefits to doing this:

  • The steam can be used again without going through the phase changes described above.
  • Reutilizing steam can save money because your boiler doesn’t have to fire as often to heat water and make steam.
  • Running your boiler less frequently is better for the environment because fewer emissions are produced.
  • Trapping steam in the system and removing air and condensate can prevent water hammer, that annoying clanging you hear sometimes in pipes and radiators.

Unless you have a fairly small property, you likely have a series of steam traps that work together along your steam pipes. These steam traps typically fall into one of three categories, as defined below, based on their mechanism of action.

Different Types of Steam Traps

Thermostatic steam traps

These traps operate by sensing temperature differentials and can tell the difference between steam and condensate at the same pressure. A sensor detects condensate and lets it drain out via a valve.

Mechanical steam traps

This type of trap uses density to detect steam and condensate via a simple float mechanism. If you have steam traps that look like buckets, you likely have mechanical steam traps.

Thermodynamic steam traps

Using both pressure measurements and volumetrics, thermodynamic steam traps are smaller and less expensive than other types of traps. However, they’re also somewhat less efficient, as they lose a bit of steam as they work.

Steam Trap Servicing

Problems we see frequently

We see many of the same problems when it comes to steam traps in New York City apartment buildings. One of the most common is the steam trap remaining open when it should close. A clue this is happening is your boiler firing more than it should because it’s working harder to produce steam. You’ll observe that your fuel bills are higher, and your water expenses may be higher too, with the automatic boiler feeder constantly sending fresh water to the boiler. If the boiler can’t keep up, you might also hear from tenants that they aren’t getting enough heat from their radiators.

Sometimes the opposite happens, and the steam trap remains closed when it should open. When this happens, you’ll find less condensate returned to the boiler. Like when a steam trap fails in the open position, this problem also results in the boiler overworking and in less heat for occupants. However, you’ll also hear water hammer in the system as that extra condensate battles with steam and air.

Dirty steam traps can result from a multitude of factors:

  • Old age and traps nearing the end of their lifespan
  • Pipes too narrow for the system
  • Poor water filtration (sediment or mineral scale accumulation)
  • Wrong or excess chemicals used in boiler water treatment
  • Lack of regular maintenance

You might have dirty steam traps if you notice valves in other parts of your boiler system are clogged, encrusted, or malfunctioning. They might leak or have unusual wear, such as hardened or cracked parts. You might also notice you’re replacing valves more often than you think is right.

Of course, you could have the cleanest and most expensive steam traps in your property. But if they’re not sized right for your boiler system, or if they’re not installed properly, they won’t get the job done. That’s why it’s essential that you have boiler professionals like Calray Boilers put your steam traps in place and service them regularly.

Every property is different, and your heating system’s unique anatomy demands a tailored approach. We can give you a consultation that examines all aspects of your system and helps you choose the right components, including steam traps for efficiency and cost savings.

Whether you would like to have your steam traps checked or upgrade your steam trap system, Calray Boilers is here to help. You can call us at 212-722-5506, or use our easy online form to schedule a service visit at your convenience.


Our Privacy Policy

Omnia Mechanical Group(the “Company”) strives to ensure the highest standards for property listings and customer information privacy. Please review the following statement to learn about our company practices and policies. Please be aware that our Privacy Policy is subject to change at any time.

1. Purpose.

This Privacy Policy (“the Policy”) provides information on how the Company uses your personal information. By agreeing to the Policy, you agree to our collection and use of your personal information as described in the Policy. This Privacy Policy is effective for all new users of Sanitaryplumbing.com.

2. Personal Information.

You can browse some areas of omniagroup.nyc (“the Website”) without being a registered user. However, certain activities do require registration. (You consent to the transfer and storage of your information by registering with omniagroup.nyc).

3. Use of Information.

Our primary purpose in collecting personal information is to provide you with a safe and user-friendly experience. For example, the Company may use your personal information to:

  • Improve our services and the Website’s content and layout;
  • Provide the services and necessary customer support you request;
  • Resolve disputes, collect fees, and troubleshoot problems;
  • Track and record customer satisfaction with our services;
  • Protect the Company against error and fraud;
  • Inform you of special promotions and announcements;
  • Enforce our agreements, terms, conditions, and policies; and
  • As otherwise described to you at the time of collection.

We may occasionally ask you to complete optional surveys. These surveys are used to improve and customize your experience with Sanitaryplumbing.com.

The Company always provides you the ability to opt-out of further communication such as promotions and surveys; see the Opt-Out section below.

The Company does not share any of your personal information with outside organizations, companies, individuals, etc. The only exception to this standard is if such a disclosure is reasonably necessary to respond to any and all legal processes.

4. Links to Other Sites.

The Website may have links to other websites that may collect personally identifiable information about you. The Company is not responsible for the privacy practices of the content of those linked websites.

5. Safety & Security Precautions.

The Website has strict security measures in place to protect you and your information from fraud. Once your information is provided to Omnia Mechanical Group, we strive to ensure the confidentiality of your identity and information.

6. Opt-Out.

The Company provides you with the opportunity to opt-out of receiving promotional and other non-essential, marketing-related communications from Omnia Mechanical Group. If you would like to opt-out of these select communications, please see any of the Company’s email communications and follow the directions indicated.

7. Account Protection.

Your password ensures the security of your account. When choosing a password, the Company suggests using various characters. It is highly recommended that you do not disclose your Sanitaryplumbing.com password to anyone. (If you do disclose your password or your personal information with others, you are responsible for all actions taken in the name of your account.) If the security of your password is compromised for any reason, please contact the Company immediately.

8. Accuracy of Information

The Company does not guarantee the accuracy of information for any and all of its properties on the Website, and is not responsible for any errors or misrepresentations (made by Renters, the Client, or otherwise).

9. Cookies

The Company may place a small cookie on your computer’s hard drive. This allows us to personalize your use on the Website. In order to maximize the functionality and usability of the Website, you must set your browser’s preferences to allow both permanent and temporary cookies.

10. Changing Your Personal Information.

Should your personal information change, please immediately update your information on the Website. This will ensure the accuracy of our records. The Company does retain personal information from closed accounts in order to comply with law and collect and disburse any fees owed.

11. Third Parties

This Privacy Policy addresses only the use of information we collect from you. Since omniagroup.nyc does not control the privacy policies of third parties, you are subject to the privacy policies of those third parties. It is advisable that you consult with the management of third parties before you disclose your personal information to others.

12. General

We may amend this Privacy Policy at any time by posting the amended terms on the Website. All amended terms are immediately effective after they are initially posted on the Website.

13. Privacy Policy Questions & Concerns

Questions and/or concerns regarding the Policy should be emailed to the following email address: info@omniagroup.nyc.